Step taken to prepare the size paste for sizing

Step Taken to prepared the size paste 

1.Take standard volume 700 lit water  normal temperature into pre mixture water flow meter start the stirring
2. Properly way all chemical required
3. Add a modify ,starches PVA, acrylic Binder slowly into pre mixture
4. Stirring mixture for 15 min
5 transfer  the pre  mixture into the closed vessel cooker
6. Close all open wall of the cooker
7.Heat the cooker mixture with injection of steam will Auto cut  when cooker cooker temperature reaches limit is 100 to 110 degree Celsius, take around 30 to 35 minutes
8. Cook the mixture for another 45 minute temperature of the cooker reach 120 degrees celsius depend upon the size recipe
9. Start the stirr of storage Vessel then the Transfer cooked  respective  to storage  vessel
10. Add the lubricant with the size paste at storage vessel
11. Maintain the storage vessel temperature 80 to 90 degree Celsius
12. Paste  ready to transfer the size box to the sizing machine

    

Comments

Post a Comment

Popular posts from this blog

Advantages and Disadvantages of Shuttle Loom/Merits and Limitation of Shuttle Loom

Image
Merits And Limitation Of Shuttle Loom A.Advantages /Merit Of Shuttle Loom - 1.The power loom suitable for the various fabric. i.e It is versatile loom. 2. It is suitable for smaller lot of fabric 3. As loom operate at less speed, warp  preparation is not demanding 4. Quality demand of yarn (warp and weft ) is less 5. The capital investment is less 6. Required very less amount of climate control. 7. There is no need for separate Selvedge  mechanism. Automatic selvedge form . 8. The power requirement less technical equipment. 9.  The labour is easily available and very high skill is not required. 10.   The Spare part cheap and easily available in market 11. It can be fitted with Dobby and Jacquard . Disadvantages/ limitation of shutt le loom 1. It  use half kg of shuttle to carry a yarn  having a weight of 0. 2 gm/m. 2. It is wasting lot of kinetic energy of the shuttle in the shuttle box. 3. It give  more wear...
Read more

Rapier weft Insertion System

Image
Repier Weft Insertion system -      The picking or weft  insertion system is based on modified repair principle, two carriers  entering the warp Shed  simultaneously from each side of the l oom and meeting almost half way through the shed. These are two basic type of rapier heads: 1) Loop transfer rapier machine-Gabler Principle ,  2) Tip transfer repair machine -Dewas principle.    In the Gabler system the weft  is never gripped. It is placed in a slot 'A' in the right rapier head and as the rapier advance towards the centre of the Loom, the yarn  passes from its clamped position round the head,  to the supply package in the form of hair pin .When  the head meet at the centre of the loom, the smaller left hand head , enters the yarn  carrying right hand head. The thread at 'A' is passed under the spring loaded cover guide at 'B' and  as the left hand rapier is withdrawn,it repositions the weft ...
Read more

PRINCIPLES OF YARN CLEARING /YARN CLEARING IN WINDING / ASSESSMENTS OF CLEARER PERFORMANCE

Image
Objective of yarn clearing -     Objective of yarn clearing is to remove objectionable faults from the yarn / supply package Principles of measurement of yarn faults/Yarn diameter    Two principles are used in morden winders for identification of yarn faults   1. Capacitance principle    2.Optical principle  1.Capacitance principle - Working Principle- :    When yarn pass through two capacitor parallel plate the electrical signal changes / produce which is proportional to change in mass per unit length.  Capacitance (C) = εA /d                                 C= charge/Voltage Working -:       In the capacitor electronic yarn clear device is measurement of yarn mass per given test length        Any change in mass of yarn then the set value to makes corresponding change in a capacitance. Th...
Read more